09/2008 150 g ene ra l t e ch ni ca l d ata d ielectric: polypropylene flm. plates: metal layer deposited by evaporation under vacuum. winding: non-inductive type. l eads: tinned wire. protection: plastic case, thermosetting resin flled. box material is solvent resistant and fame retardant according to ul94 v0. m arking: manufacturers logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric code, climatic category, passive fammability category, manufacturing date code, approvals, manufacturing plant. climatic category: 40/110/56 iec 60068-1 o perating temperature range: -40 to +110c related documents: iec 60384-14, en 60384-14. ele ctr i ca l charact e r i st i cs rated voltage (v r ): 275vac (50/60hz) / 560 vdc 300vac (50/60hz) / 630 vdc capacitance range: 0.01 f to 10 f capacitance values: e6 series (iec 60063 norm). capacitance tolerances (measured at 1 khz) : 10% (k); 20% (m); tolerance 5% (j) available upon request d issipation factor ( d f): tg 10 -4 at +25c 5c: 10 (6)* at 1khz * typical value i nsulation resistance: test conditions temperature: +25c 5c voltage charge time: 1 min voltage charge: 100 vdc performance 1x10 5 m ? (5x10 5 m ? ) * for c 0.33 f 30000 s (150000 s ) * for c > 0.33 f * typical value test voltage between terminations (on all pieces) : 1500vac for 1 s + 2200vdc for 1 s at +25c 5c r.46 x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perti es typical applications : interference suppression and ?across-the-line? applications. suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. pr o duct c o de: R46 n ote: r.46 series has replaced the 1.40 series and 1.47 series. for new design we suggest the use of the r.46 series. ? d 0.05 p 15 22.5 p 27.5 p = 37.5 0.6 or 0.8* 0.8 1 *see size table. all dimensions are in mm. loose taped fig.1 fig.2 t e st me th od a nd p e rf o r m a n c e d amp heat, steady state: test conditions 1st temperature: +40c 2c relative humidity (rh): 93% 2% test duration: 56 days test conditions 2nd temperature: +60c 2c relative humidity (rh): 95% 2% test duration: 500 hours performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 5% insulation resistance: 50% of initial limit. e ndurance: test conditions temperature: +110c 2c test duration: 1000 h voltage applied: 1.25 x v r +1000vac 0.1 s/h performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 10% insulation resistance: 50% of initial limit. resistance to soldering heat: test conditions solder bath temperature: +260c 5c dipping time (with heat screen):10 s 1 s performance capacitance change | ? c/c|: 2% winding scheme single sided metallized polypropylene flm pitch box thickness (b) maximum dimensions (mm) (mm) (mm) b max h max l max 10.0 all b +0.2 h +0.1 l +0.2 15.0 <7.5 b +0.2 h +0.1 l +0.3 15.0 7.5 b +0.2 h +0.1 l +0.5 22.5 all b +0.2 h +0.1 l +0.3 27.5 all b +0.2 h +0.1 l +0.3 37.5 all b +0.3 h +0.1 l +0.3 insulated rigid leads insulated fexible leads 0.5mm 2
09/2008 151 r.46 x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perti es appr o va l s (**) enec mark has replaced all the following european national marks: all dimensions are in mm e12 series available upon request table 1 standard packaging style l ead length (mm) taping style o rdering code (digit 10 to 11) p 2 (mm) fig. (no.) pitch (mm) amm o -pack amm o -pack 12.70 19.05 1 2 10.0/15.0 22.5 dq dq reel ? 500mm reel ? 500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 ck ck loose, short leads loose, long leads loose, long leads 04 +2 25 -1/+2 30 +5 00 50 40 loose, insulated rigid leads loose, insulated fexible leads 30 +5 150 5 51 52 note: ammo-pack is the preferred packaging for taped version. for capacitor connected in serial with main line (two - phase and three - phase net) application, please read the sh o rt guide t o ch oo se the right film capacit o rs and contact our technical service for choosing the safest solution. rated cap. 275 vac / 560 vdc std dimensions ? d m ax dv/dt at 390vdc part n umber b h l p (v/ s) 0.010 f 4.0 9.0 13.0 10.0 0.6 500 R46 kf 2100 - - n0 - 0.015 f 4.0 9.0 13.0 10.0 0.6 500 R46 kf 2150 - - n0 - 0.022 f 4.0 9.0 13.0 10.0 0.6 500 R46 kf 2220 - - n0 - 0.033 f 5.0 1 1.0 13.0 10.0 0.6 500 R46 kf 2330 - - m1 - 0.047 f 5.0 1 1.0 13.0 10.0 0.6 500 R46 kf 2470 - - n0 - 0.068 f 6.0 12.0 13.0 10.0 0.6 500 R46 kf 2680 - - m1 - 0.10 f 6.0 12.0 13.0 10.0 0.6 500 R46 kf 3100 - - m1 m 0.010 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2100 - - 01 - 0.015 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2150 - - 01 - 0.022 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2220 - - 01 - 0.033 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2330 - - 01 - 0.047 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2470 - - 01 - 0.068 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 2680 - - 01 - 0.10 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 3100 - - m1 - 0.15 f 6.0 12.0 18.0 15.0 0.6 400 R46 ki 3150 - - m2 - 0.15 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3150 - - l2 - 0.22 f 7.5 13.5 18.0 15.0 0.6 400 R46 ki 3220 - - m2 - 0.22 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3220 - - l2 - 0.22 f 6.0 17.5 18.0 15.0 0.6 400 R46 ki 3220 - - 02 - 0.33 f 8.5 14.5 18.0 15.0 0.6 400 R46 ki 3330 - - n0 - 0.33 f 10.0 16.0 18.0 15.0 0.8 400 R46 ki 3330 - - m1 - 0.33 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3330 - - n1 m 0.33 f 7.5 18.5 18.0 15.0 0.8 400 R46 ki 3330 - - 02 - 0.33 f 13.0 12.0 18.0 15.0 0.8 400 R46 ki 3330 - - 01 - 0.47 f 7.5 18.5 18.0 15.0 0.8 400 R46 ki 3470 - - 02 m 0.47 f 10.0 16.0 18.0 15.0 0.8 400 R46 ki 3470 - - n0 m 0.47 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3470 - - m1 - 0.56 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3560 - - n0 - 0.60 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3600 - - n0 - 0.15 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3150 - - 01 - 0.22 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3220 - - m1 - 0.33 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3330 - - n0 - 0.47 f 7.0 16.0 26.5 22.5 0.8 200 R46 kn 3470 - - n0 - 0.68 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 3680 - - m2 - 1.0 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 4100 - - n2 m 1.0 f 11.0 20.0 26.5 22.5 0.8 200 R46 kn 4100 - - n1 - 0.47 f 9.0 17.0 32.0 27.5 0.8 150 R46 kr 3470 - - 01 - 0.68 f 9.0 17.0 32.0 27.5 0.8 150 R46 kr 3680 - - m1 - 1.0 f 11.0 20.0 32.0 27.5 0.8 150 R46 kr 4100 - - m1 - 1.5 f 13.0 22.0 32.0 27.5 0.8 150 R46 kr 4150 - - m1 - 2.2 f 13.0 25.0 32.0 27.5 0.8 150 R46 kr 4220 - - m2 - 2.2 f 14.0 28.0 32.0 27.5 0.8 150 R46 kr 4220 - - m1 - 3.3 f 18.0 33.0 32.0 27.5 0.8 150 R46 kr 4330 - - m2 - 4.7 f 18.0 33.0 32.0 27.5 0.8 150 R46 kr 4470 - - m2 - 4.7 f 22.0 37.0 32.0 27.5 0.8 150 R46 kr 4470 - - m1 - 1.5 f 11.0 22.0 41.5 37.5 1.0 100 R46 kw 4150 - - m1 - 2.2 f 11.0 22.0 41.5 37.5 1.0 100 R46 kw 4220 - - m2 m 2.2 f 13.0 24.0 41.5 37.5 1.0 100 R46 kw 4220 - - m1 - 3.3 f 16.0 28.5 41.5 37.5 1.0 100 R46 kw 4330 - - m1 - 4.7 f 16.0 28.5 41.5 37.5 1.0 100 R46 kw 4470 - - m2 m 4.7 f 19.0 32.0 41.5 37.5 1.0 100 R46 kw 4470 - - m1 - 6.8 f 20.0 40.0 41.5 37.5 1.0 100 R46 kw 4680 - - m2 - 6.8 f 24.0 44.0 41.5 37.5 1.0 100 R46 kw 4680 - - m1 - 10.0 f 30.0 45.0 41.5 37.5 1.0 100 R46 kw 5100 - - m1 - rated voltage (k=275vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) (**) enec iec 60384-14 class x2 file no.v4413 ul 1414 (up to 1 f, 85c; 250vac) across-the-line file no.e97797 csa - c22.2 no.1 (up to 1 f, 85c; 250vac) across-the-line certifed for canada file no.e97797 ul 1283 (310 vac) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310 vac) electromagnetic interference filters certifed for canada file no.e85238 gb/t 14472 class x2 file cqc03001008199 cqc03001008842 approved according to iec 60384-14 according to iec 60065 not for use in series with the mains. see www.kemet.com for more information. not for new design.
09/2008 152 r.46 x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perti es appr o va l s . (**) enec mark has replaced all the following european national marks: table 1 standard packaging style l ead length (mm) taping style o rdering code (digit 10 to 11) p 2 (mm) fig. (no.) pitch (mm) amm o -pack amm o -pack 12.70 19.05 1 2 10.0/15.0 22.5 dq dq reel ? 500mm reel ? 500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 ck ck loose, short leads loose, long leads loose, long leads 04 +2 25 -1/+2 30 +5 00 50 40 loose, insulated rigid leads loose, insulated fexible leads 30 +5 150 5 51 52 note: ammo-pack is the preferred packaging for taped version. for capacitor connected in serial with main line (two - phase and three - phase net) application, please read the sh o rt guide t o ch oo se the right film capacit o rs and contact our technical service for choosing the safest solution. rated voltage (k=275vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) all dimensions are in mm e12 series available upon request (**) enec iec 60384-14 class x2 file no.v4413 ul 1414 (up to 1 f, 85c; 250vac) across-the-line file no.e97797 csa - c22.2 no.1 (up to 1 f, 85c; 250vac) across-the-line certifed for canada file no.e97797 ul 1283 (310 vac) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310 vac) electromagnetic interference filters certifed for canada file no.e85238 gb/t 14472 class x2 file cqc03001008199 cqc03001008842 approved according to iec 60384-14 according to iec 60065 rated cap. 275 vac / 560 vdc std dimensions ? d m ax dv/dt at 390vdc part n umber b h l p (v/ s) 0.033 f 4.0 9.0 13.0 10.0 0.6 500 R46 kf 2330 - - p0 - 0.047 f 4.0 9.0 13.0 10.0 0.6 500 R46 kf 2470 - - p0 - 0.068 f 5.0 1 1.0 13.0 10.0 0.6 500 R46 kf 2680 - - p0 - 0.1 f 5.0 1 1.0 13.0 10.0 0.6 500 R46 kf 3100 - - p1 m 0.1 f 6.0 12.0 13.0 10.0 0.6 500 R46 kf 3100 - - p0 - 0.15 f 6.0 12.0 13.0 10.0 0.6 500 R46 kf 3150 - - p0 m 0.15 f 5.0 1 1.0 18.0 15.0 0.6 400 R46 ki 3150 - - p0 - 0.22 f 6.0 12.0 18.0 15.0 0.6 400 R46 ki 3220 - - p0 - 0.33 f 7.5 13.5 18.0 15.0 0.6 400 R46 ki 3330 - - p0 - 0.33 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3330 - - p1 0.33 f 6.0 17.5 18.0 15.0 0.6 400 R46 ki 3330 - - p2 - 0.47 f 8.5 14.5 18.0 15.0 0.6 400 R46 ki 3470 - - p0 0.47 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3470 - - p1 m 0.47 f 6.0 17.5 18.0 15.0 0.6 400 R46 ki 3470 - - p2 m 0.47 f 7.5 18.5 18.0 15.0 0.8 400 R46 ki 3470 - - p3 - 0.68 f 10.0 16.0 18.0 15.0 0.8 400 R46 ki 3680 - - p1 m 0.68 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3680 - - p0 - 0.82 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3820 - - p0 m 0.47 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3470 - - p1 - 0.56 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3560 - - p1 m 0.56 f 7.0 16.0 26.5 22.5 0.8 200 R46 kn 3560 - - p0 - 0.68 f 7.0 16.0 26.5 22.5 0.8 200 R46 kn 3680 - - p0 - 1.0 f 8.5 17.0 26.5 22.5 0.8 200 R46 kn 4100 - - p1 m 1.0 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 4100 - - p0 - 1.5 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 4150 - - p1 m 1.5 f 11.0 20.0 26.5 22.5 0.8 200 R46 kn 4150 - - p0 - 2.2 f 13.0 22.0 26.5 22.5 0.8 200 R46 kn 4220 - - p0 m 1.0 f 9.0 17.0 32.0 27.5 0.8 150 R46 kr 4100 - - p0 - 1.5 f 11.0 20.0 32.0 27.5 0.8 150 R46 kr 4150 - - p0 - 2.2 f 13.0 22.0 32.0 27.5 0.8 150 R46 kr 4220 - - p0 - 3.3 f 14.0 28.0 32.0 27.5 0.8 150 R46 kr 4330 - - p0 - 4.7 f 14.0 28.0 32.0 27.5 0.8 150 R46 kr 4470 - - p1 m 4.7 f 18.0 33.0 32.0 27.5 0.8 150 R46 kr 4470 - - p0 - 6.8 f 22.0 37.0 32.0 27.5 0.8 150 R46 kr 4680 - - p0 - 2.2 f 11.0 22.0 41.5 37.5 1.0 100 R46 kw 4220 - - p0 - 3.3 f 13.0 24.0 41.5 37.5 1.0 100 R46 kw 4330 - - p0 - 4.7 f 16.0 28.5 41.5 37.5 1.0 100 R46 kw 4470 - - p0 - 6.8 f 19.0 32.0 41.5 37.5 1.0 100 R46 kw 4680 - - p0 - 10.0 f 20.0 40.0 41.5 37.5 1.0 100 R46 kw 5100 - - p0 - not for use in series with the mains. see www.kemet.com for more information.
09/2008 153 r.46 x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perties appr o va l s table 1 standard packaging style lead length (mm) taping style ordering code (digit 10 to 1 1) p 2 (mm) fig. (no.) pitch (mm) ammo -pack ammo -pack 12.70 19.05 1 2 10.0/15.0 22.5 dq dq reel ? 500mm reel ? 500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 ck ck loose, short leads loose, long leads loose, long leads 04 +2 25 -1/+2 30 +5 00 50 40 loose, insulated rigid leads loose, insulated fexible leads 30 +5 150 5 51 52 note: ammo-pack is the preferred packaging for taped version. (**) enec mark has replaced all the following european national marks: rated voltage (3=300vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) all dimensions are in mm e12 series available upon request for capacitor connected in serial with main line (two - phase and three - phase net) application, please read the sh o rt guide t o ch oo se the right film capacit o rs and contact our t echnical service for choosing the safest solution. (**) enec iec 60384-14 class x2 file no.v4413 ul 1414 (up to 1 f, 85c; 250vac) across-the-line file no.e97797 csa - c22.2 no.1 (up to 1 f, 85c; 250vac) across-the-line certifed for canada file no.e97797 ul 1283 (310 v ac) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310 v ac) electromagnetic interference filters certifed for canada file no.e85238 gb/t 14472 class x2 filecqc03001008199 cqc03001008842 approved according to iec 60384-14 according to iec 60065 rated cap. 300 vac / 630 vdc std dimensions ? d max dv/dt at 390vdc part number b h l p (v/ s) 0.010 f 4.0 9.0 13.0 10.0 0.6 500 R46 3f 2100 - - n0 - 0.015 f 4.0 9.0 13.0 10.0 0.6 500 R46 3f 2150 - - n0 - 0.022 f 4.0 9.0 13.0 10.0 0.6 500 R46 3f 2220 - - n0 - 0.033 f 5.0 11.0 13.0 10.0 0.6 500 R46 3f 2330 - - m1 - 0.047 f 5.0 11.0 13.0 10.0 0.6 500 R46 3f 2470 - - n0 - 0.068 f 6.0 12.0 13.0 10.0 0.6 500 R46 3f 2680 - - m1 - 0.10 f 6.0 12.0 13.0 10.0 0.6 500 R46 3f 3100 - - m1 m 0.010 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2100 - - 01 - 0.015 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2150 - - 01 - 0.022 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2220 - - 01 - 0.033 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2330 - - 01 - 0.047 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2470 - - 01 - 0.068 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 2680 - - 01 - 0.10 f 5.0 11.0 18.0 15.0 0.6 400 R46 3i 3100 - - m1 - 0.15 f 6.0 12.0 18.0 15.0 0.6 400 R46 3i 3150 - - m2 - 0.15 f 9.0 12.5 18.0 15.0 0.6 400 R46 3i 3150 - - l2 - 0.22 f 7.5 13.5 18.0 15.0 0.6 400 R46 3i 3220 - - m2 - 0.22 f 9.0 12.5 18.0 15.0 0.6 400 R46 3i 3220 - - l2 - 0.22 f 6.0 17.5 18.0 15.0 0.6 400 R46 3i 3220 - - 02 - 0.33 f 8.5 14.5 18.0 15.0 0.6 400 R46 3i 3330 - - n0 - 0.33 f 10.0 16.0 18.0 15.0 0.8 400 R46 3i 3330 - - m1 - 0.33 f 7.5 18.5 18.0 15.0 0.8 400 R46 3i 3330 - - 02 - 0.33 f 13.0 12.0 18.0 15.0 0.8 400 R46 3i 3330 - - 01 - 0.47 f 10.0 16.0 18.0 15.0 0.8 400 R46 3i 3470 - - n0 m 0.47 f 11.0 19.0 18.0 15.0 0.8 400 R46 3i 3470 - - m1 - 0.56 f 11.0 19.0 18.0 15.0 0.8 400 R46 3i 3560 - - n0 - 0.60 f 11.0 19.0 18.0 15.0 0.8 400 R46 3i 3600 - - n0 - 0.15 f 6.0 15.0 26.5 22.5 0.8 200 R46 3n 3150 - - 01 - 0.22 f 6.0 15.0 26.5 22.5 0.8 200 R46 3n 3220 - - m1 - 0.33 f 6.0 15.0 26.5 22.5 0.8 200 R46 3n 3330 - - n0 - 0.47 f 7.0 16.0 26.5 22.5 0.8 200 R46 3n 3470 - - n0 - 0.68 f 10.0 18.5 26.5 22.5 0.8 200 R46 3n 3680 - - m2 - 1.0 f 10.0 18.5 26.5 22.5 0.8 200 R46 3n 4100 - - n2 m 1.0 f 11.0 20.0 26.5 22.5 0.8 200 R46 3n 4100 - - n1 - 0.47 f 9.0 17.0 32.0 27.5 0.8 150 R46 3r 3470 - - 01 - 0.68 f 9.0 17.0 32.0 27.5 0.8 150 R46 3r 3680 - - m1 - 1.0 f 11.0 20.0 32.0 27.5 0.8 150 R46 3r 4100 - - m1 - 1.5 f 13.0 22.0 32.0 27.5 0.8 150 R46 3r 4150 - - m1 - 2.2 f 13.0 25.0 32.0 27.5 0.8 150 R46 3r 4220 - - m2 - 2.2 f 14.0 28.0 32.0 27.5 0.8 150 R46 3r 4220 - - m1 - 3.3 f 18.0 33.0 32.0 27.5 0.8 150 R46 3r 4330 - - m2 - 4.7 f 18.0 33.0 32.0 27.5 0.8 150 R46 3r 4470 - - m2 - 4.7 f 22.0 37.0 32.0 27.5 0.8 150 R46 3r 4470 - - m1 - 1.5 f 11.0 22.0 41.5 37.5 1.0 100 R46 3w 4150 - - m1 - 2.2 f 11.0 22.0 41.5 37.5 1.0 100 R46 3w 4220 - - m2 m 2.2 f 13.0 24.0 41.5 37.5 1.0 100 R46 3w 4220 - - m1 - 3.3 f 16.0 28.5 41.5 37.5 1.0 100 R46 3w 4330 - - m1 - 4.7 f 16.0 28.5 41.5 37.5 1.0 100 R46 3w 4470 - - m2 m 4.7 f 19.0 32.0 41.5 37.5 1.0 100 R46 3w 4470 - - m1 - 6.8 f 20.0 40.0 41.5 37.5 1.0 100 R46 3w 4680 - - m2 - 6.8 f 24.0 44.0 41.5 37.5 1.0 100 R46 3w 4680 - - m1 - 10.0 f 30.0 45.0 41.5 37.5 1.0 100 R46 3w 5100 - - m1 - not for use in series with the mains. see www.kemet.com for more information.
09/2008 154 r.46 x2 class (iec 60384-14) - mkp me tallized pol ypropylene f ilm capacit or self-healing pro perties typical applications : interference suppression and ?across- the-line? applications. suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. pr o duct co de: R46 ne w 125c rated cap. 275 vac / 560 vdc std dimensions ? d m ax dv/dt at 390vdc (v/ s) part n umber b h l p 0.010 f 5.0 1 1.0 13.0 10.0 0.6 500 R46 k f 2100 - - h1 - 0.015 f 5.0 11.0 13.0 10.0 0.6 500 R46 k f 2150 - - h1 - 0.022 f 5.0 11.0 13.0 10.0 0.6 500 R46 k f 2220 - - h1 - 0.033 f 5.0 11.0 13.0 10.0 0.6 500 R46 k f 2330 - - h1 - 0.047 f 6.0 12.0 13.0 10.0 0.6 500 R46 k f 2470 - - h1 - 0.068 f 6.0 12.0 13.0 10.0 0.6 500 R46 k f 2680 - - h1 m 0.010 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2100 - - h1 - 0.015 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2150 - - h1 - 0.022 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2220 - - h1 - 0.033 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2330 - - h1 - 0.047 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2470 - - h1 - 0.068 f 5.0 11.0 18.0 15.0 0.6 400 R46 k i 2680 - - h1 - 0.10 f 6.0 12.0 18.0 15.0 0.6 400 R46 k i 3100 - - h1 - 0.15 f 6.0 17.5 18.0 15.0 0.6 400 R46 k i 3150 - - h2 - 0.15 f 9.0 12.5 18.0 15.0 0.6 400 R46 k i 3150 - - h3 - 0.15 f 7.5 13.5 18.0 15.0 0.6 400 R46 k i 3150 - - h1 - 0.22 f 8.5 14.5 18.0 15.0 0.6 400 R46 k i 3220 - - h1 - 0.22 f 6.0 17.5 18.0 15.0 0.6 400 R46 k i 3220 - - h2 m 0.22 f 9.0 12.5 18.0 15.0 0.6 400 R46 k i 3220 - - h3 m 0.22 f 7.5 18.5 18.0 15.0 0.8 400 R46 k i 3220 - - h4 - 0.33 f 10.0 16.0 18.0 15.0 0.8 400 R46 k i 3330 - - h1 m 0.33 f 7.5 18.5 18.0 15.0 0.8 400 R46 k i 3330 - - h2 m 0.33 f 13.0 12.0 18.0 15.0 0.8 400 R46 k i 3330 - - h3 m 0.47 f 11.0 19.0 18.0 15.0 0.8 400 R46 k i 3470 - - h1 m 0.15 f 6.0 15.0 26.5 22.5 0.8 200 R46 k n 3150 - - h1 - 0.22 f 6.0 15.0 26.5 22.5 0.8 200 R46 k n 3220 - - h1 - 0.33 f 7.0 16.0 26.5 22.5 0.8 200 R46 k n 3330 - - h1 - 0.47 f 10.0 18.5 26.5 22.5 0.8 200 R46 k n 3470 - - h1 - 0.68 f 11.0 20.0 26.5 22.5 0.8 200 R46 k n 3680 - - h1 - 1.0 f 13.0 22.0 26.5 22.5 0.8 200 R46 k n 4100 - - h1 - 300vac available upon request e12 series available upon request all dimensions are in mm loose taped fig.1 fig.2 rated voltage (k=275vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) for capacitor connected in serial with main line (two - phase and three - phase net) application, please read the sh o rt guide t o ch oo se the right film capacit o rs and contact our t echnical service for choosing the safest solution. ? d 0.05 p 15 p = 22.5 0.6 or 0.8* 0.8 *see size table. all dimensions are in mm. general technical d ata dielectric: polypropylene flm. plates: metal layer deposited by evaporation under vacuum. winding: non-inductive type. l eads: tinned wire. protection: plastic case, thermosetting resin flled. box material is solvent resistant and fame retardant according to ul94 v0. marking: manufacturers logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric code, climatic category, passive fammability category, manufacturing date code, approvals, manufacturing plant. climatic category: 40/125/56 iec 60068-1 operating temperature range: -40 to +125c related documents: iec 60384-14; en 60384-14 electrica l characteristics rated voltage (v r ): 275 vac (50/60hz) / 560 vdc capacitance range: 0.01f to 1f test method and performance endurance: test conditions temperature: +125c2c test duration: 1000 h voltage applied: 1.25 x v r +1000vac 0.1 s/h performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ?c/c|: 10% insulation resistance: 50% of initial limit. a ppr o v a ls (**) enec iec 60384-14 class x2 file no.ca08.00063 ul 1414 (up to 1 f, 85c; 250vac) across-the-line file no.e97797 csa - c22.2 no.1 (up to 1 f, 85c; 250vac) across-the-line certifed for canada file no.e97797 ul 1283 (310 v ac) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310 v ac) electromagnetic interference filters certifed for canada file no.e85238 approved according to iec 60384-14 according to iec 60065 (**) enec mark has replaced all the following european national marks: not for use in series with the mains. see www.kemet.com for more information.
09/2008 155 ? d 0.05 p 15 22.5 p 27.5 p = 37.5 0.6 or 0.8* 0.8 1.0 *see size table. all dimensions are in mm. general technical d ata dielectric: polypropylene flm. plates: metal layer deposited by evaporation under vacuum. winding: non-inductive type. l eads: tinned wire. protection: plastic case, thermosetting resin flled. box material is solvent resistant and fame retardant according to ul94 v0. marking: manufacturers logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric code, climatic category, passive fammability category, manufacturing date code, approvals, manufacturing plant. climatic category: 40/110/56 iec 60068-1 operating temperature range: -40 to +110c related documents: iec 60384-14, en 60384-14. electrica l characteristics rated voltage (v r ): 275vac (50/60hz) / 560 vdc capacitance range: 0.022 f to 10 f capacitance values: e6 series (iec 60063 norm). capacitance tolerances (measured at 1 khz) : 10% (k); 20% (m). tolerance 5% (j) available upon request dissipation factor (df): tg 10 -4 at +25c 5c: 15 (8)* at 1khz * typical value insulation resistance: test conditions temperature: +25c 5c voltage charge time: 1 min voltage charge: 100 vdc performance 1x10 5 m ? (5x10 5 m ? ) * for c 0.33 f 30000 s (150000 s ) * for c > 0.33 f * typical value test voltage between terminations (on all pieces) : 1500vac for 1 s + 2200vdc for 1 s at +25c 5c r.46 s version x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perties typical applications : this special R46 release is designed for applications in series with the main . pro duct c o de: R46 pitch box thickness (b) maximum dimensions (mm) (mm) (mm) b max h max l max 10.0 all b +0.2 h +0.1 l +0.2 15.0 <7.5 b +0.2 h +0.1 l +0.3 15.0 7.5 b +0.2 h +0.1 l +0.5 22.5 all b +0.2 h +0.1 l +0.3 27.5 all b +0.2 h +0.1 l +0.3 37.5 all b +0.3 h +0.1 l +0.3 test method and performance damp heat, steady state: test conditions 1st temperature: +40c 2c relative humidity (rh): 93% 2% test duration: 56 days test conditions 2nd temperature: +60c 2c relative humidity (rh): 95% 2% test duration: 500 hours test conditions 3rd temperature: +40c 2c relative humidity (rh): 93% 2% test duration: 500 hours voltage value: 230 vac, 50 hz performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 5% insulation resistance: 50% of initial limit. endurance: test conditions temperature: +110c 2c test duration: 1000 h voltage applied: 1.25 x v r +1000vac 0.1 s/h performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 10% insulation resistance: 50% of initial limit. resistance to soldering heat: test conditions solder bath temperature: +260c 5c dipping time (with heat screen):10 s 1 s performance capacitance change | ? c/c|: 2% loose taped fig.1 fig.2 not for use in series with the mains. see www.kemet.com for more information. not for new design.
09/2008 156 rated cap. (*) 275 vac / 560 vdc std dimensions ? d m ax dv/dt at 390vdc part number b h l p (v/ s) 0.010 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2100 - - s0 - 0.015 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2150 - - s0 - 0.022 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2220 - - s0 - 0.033 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2330 - - s0 - 0.047 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2470 - - s1 - 0.068 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 2680 - - s0 - 0.10 f 5.0 11.0 18.0 15.0 0.6 400 R46 ki 3100 - - s1 m 0.10 f 6.0 12.0 18.0 15.0 0.6 400 R46 ki 3100 - - s0 - 0.15 f 6.0 12.0 18.0 15.0 0.6 400 R46 ki 3150 - - s1 m 0.15 f 7.5 13.5 18.0 15.0 0.6 400 R46 ki 3150 - - s0 - 0.15 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3150 - - s3 - 0.22 f 7.5 13.5 18.0 15.0 0.6 400 R46 ki 3220 - - s1 m 0.22 f 8.5 14.5 18.0 15.0 0.6 400 R46 ki 3220 - - s0 - 0.22 f 6.0 17.5 18.0 15.0 0.6 400 R46 ki 3220 - - s2 - 0.22 f 9.0 12.5 18.0 15.0 0.6 400 R46 ki 3220 - - s3 - 0.33 f 13.0 12.0 18.0 15.0 0.8 400 R46 ki 3330 - - s1 - 0.33 f 8.5 14.5 18.0 15.0 0.8 400 R46 ki 3330 - - s3 m 0.33 f 10.0 16.0 18.0 15.0 0.8 400 R46 ki 3330 - - s0 - 0.33 f 7.5 18.5 18.0 15.0 0.8 400 R46 ki 3330 - - s2 - 0.47 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3470 - - s0 - 0.47 f 10.0 16.0 18.0 15.0 0.8 400 R46 ki 3470 - - s1 m 0.56 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3560 - - s0 - 0.68 f 11.0 19.0 18.0 15.0 0.8 400 R46 ki 3680 - - s0 m 0.22 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3220 - - s0 - 0.33 f 6.0 15.0 26.5 22.5 0.8 200 R46 kn 3330 - - s1 m 0.33 f 7.0 16.0 26.5 22.5 0.8 200 R46 kn 3330 - - s0 - 0.47 f 7.0 16.0 26.5 22.5 0.8 200 R46 kn 3470 - - s1 m 0.47 f 8.5 17.0 26.5 22.5 0.8 200 R46 kn 3470 - - s0 - 0.68 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 3680 - - s0 - 1.0 f 10.0 18.5 26.5 22.5 0.8 200 R46 kn 4100 - - s2 m 1.0 f 11.0 20.0 26.5 22.5 0.8 200 R46 kn 4100 - - s1 - 1.2 f 13.0 22.0 26.5 22.5 0.8 200 R46 kn 4120 - - s0 - 0.47 f 9.0 17.0 32.0 27.5 0.8 150 R46 kr 3470 - - s0 - 0.68 f 9.0 17.0 32.0 27.5 0.8 150 R46 kr 3680 - - s1 - 1.0 f 11.0 20.0 32.0 27.5 0.8 150 R46 kr 4100 - - s1 - 1.5 f 13.0 22.0 32.0 27.5 0.8 150 R46 kr 4150 - - s1 - 2.2 f 13.0 25.0 32.0 27.5 0.8 150 R46 kr 4220 - - s2 - 3.3 f 18.0 33.0 32.0 27.5 0.8 150 R46 kr 4330 - - s2 - 4.7 f 18.0 33.0 32.0 27.5 0.8 150 R46 kr 4470 - - s2 - 1.5 f 11.0 22.0 41.5 37.5 1.0 100 R46 kw 4150 - - s1 - 2.2 f 11.0 22.0 41.5 37.5 1.0 100 R46 kw 4220 - - s2 m 2.2 f 13.0 24.0 41.5 37.5 1.0 100 R46 kw 4220 - - s1 - 3.3 f 16.0 28.5 41.5 37.5 1.0 100 R46 kw 4330 - - s1 - 4.7 f 16.0 28.5 41.5 37.5 1.0 100 R46 kw 4470 - - s2 m 4.7 f 19.0 32.0 41.5 37.5 1.0 100 R46 kw 4470 - - s1 - 6.8 f 20.0 40.0 41.5 37.5 1.0 100 R46 kw 4680 - - s2 - 10.0 f 30.0 45.0 41.5 37.5 1.0 100 R46 kw 5100 - - s1 - r.46 s version x2 class (iec60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perties table 1 standard packaging style lead length (mm) taping style ordering code (digit 10 to 11) p 2 (mm) fig. (no.) pitch (mm) ammo -pack amm o -pack 12.70 19.05 1 2 10.0/15.0 22.5 dq dq reel ? 500mm reel ? 500mm 12.70 19.05 1 2 10.0/15.0 22.5/27.5 ck ck loose, short leads loose, long leads loose, long leads 04 +2 25 -1/+2 30 +5 00 50 40 loose, insulated rigid leads loose, insulated fexible leads 30 +5 150 5 51 52 (**) enec mark has replaced all the following european national marks: appr o va l s rated voltage (k=275vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) 300vac available upon request e12 series available upon request all dimensions are in mm (**) enec iec 60384-14 class x2 file no.v4413 ul 1414 (up to 1 f, 85c; 250vac) across-the-line file no.e97797 csa - c22.2 no.1 (up to 1 f, 85c; 250vac) across-the-line certifed for canada file no.e97797 ul 1283 (310 vac) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310 v ac) electromagnetic interference filters certifed for canada file no.e85238 gb/t 14472 class x2 file cqc03001008199 cqc03001008842 approved according to iec 60384-14 according to iec 60065 note: ammo-pack is the preferred packaging for taped version. not for use in series with the mains. see www.kemet.com for more information. not for new design.
09/2008 157 loose taped fig.1 fig.2 insulated rigid leads insulated fexible leads 0.5mm 2 ? d 0.05 p= 22.5 to 27.5 p = 37.5 0.8 1 all dimensions are in mm. g ene ra l t e ch ni ca l d at a d ielectric: polypropylene flm. plates: metal layer deposited by evaporation under vacuum. winding: non-inductive type. l eads: tinned wire. protection: plastic case, thermosetting resin flled. box material is solvent resistant and fame retardant according to ul94 v0. m arking: manufacturer s logo, series, capacitance, tolerance, rated voltage, capacitor class, dielectric code, climatic category, passive fammability category, manufacturing date code, approvals, manufacturing plant. climatic category: 40/110/56 iec 60068-1 o perating temperature range: -40 to +110c related documents: iec 60384-14, en 60384-14. ele ctr i ca l charact e r i st i cs rated voltage (v r ): 275vac (50/60hz) / 560 vdc 300vac (50/60hz) / 630 vdc capacitance range: 0.22 f to 10 f capacitance values: e6 series (iec 60063 norm). capacitance tolerances (measured at 1 khz) : 10% (k); 20% (m). d issipation factor ( d f): tg 10 -4 at +25c 5c: 10 (6)* at 1khz * typical value i nsulation resistance: test conditions temperature: +25c 5c voltage charge time: 1 min voltage charge: 100 vdc performance 1x10 5 m ? (5x10 5 m ? ) * for c 0.33 f 30000 s (150000 s ) * for c > 0.33 f * typical value t est voltage between terminations (on all pieces) : r.46+r capacitors with discharge resistor x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py len e f ilm cap ac i t o r self-healing pr o per ties typical applications : interference suppression and ?across-the-line? applications. suitable for use in situations where failure of the capacitor would not lead to danger of electric shock. pr o duct c o de: R46 pitch box thickness (b) maximum dimensions (mm) (mm) (mm) b max h max l max 22.5 all b +0.2 h +0.1 l +0.3 27.5 all b +0.2 h +0.1 l +0.3 37.5 all b +0.3 h +0.1 l +0.3 t e st me th od a nd p e rf o r m a n c e d amp heat, steady state: test conditions 1st temperature: +40c 2c relative humidity (rh): 93% 2% test duration: 56 days performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 5% insulation resistance: 50% of initial limit. e ndurance: test conditions temperature: +110c 2c test duration: 1000 h voltage applied: 1.25 x v r +1000vac 0.1 s/h performance dielectric strength: no dielectric breakdown or fashover at 4.3 x v r (d.c.)/1 min capacitance change | ? c/c|: 10% insulation resistance: 50% of initial limit. resistance to soldering heat: test conditions solder bath temperature: +260c 5c dipping time (with heat screen):10 s 1 s performance capacitance change | ? c/c|: 2% appr o va l s enec iec 60384-14 class x2 file no.v4413 ul 1283 (310vac-105c) electromagnetic interference filters file no.e85238 csa - c22.2 no.8 (310vac-105c) electromagnetic interference filters certifed for canada file no.e85238 approved according to iec 60384-14 according to iec 60065. not for use in series with the mains. see www.kemet.com for more information.
product code system the part number, comprising 15 digits, is formed as follows: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 r 4 6 - - digit 1 to 3 series code. digit 4 a.c. rated voltage: k = 275vac; 3 = 300vac digit 5 pitch: n = 22.5; r = 27.5; w = 37.5 mm digit 6 to 9 digits 7 - 8 - 9 indicate the frst three digits of capacitance value and the 6th digit indicates the number of zeros that must be added to obtain the rated capacitance in pf. digit 10 to 11 mechanical version and/or packaging (table 1) digit 12 identifes the dimensions and electrical characteristics. digit 13 internal use digit 14 capacitance tolerance: k= 10%; m= 20% digit 15 value of the discharge resistor (tolerance 10%) according to the following table*: r.46+r capacitors with discharge resistor x2 class (iec 60384-14) - mkp series me ta llized p ol y pr o py lene f ilm capac i t o r self-healing pr o perties pro duct code: R46 table 1 standard packaging style lead length (mm) t aping style o rdering code (digit 10 to 1 1) p 2 (mm) fig. (no.) pitch (mm) reel ? 500mm 19.05 2 22.5/27.5 ck loose, short leads loose, long leads loose, long leads 04 +2 25 -1/+2 30 +5 00 50 40 loose, insulated rigid leads loose, insulated fexible leads 30 +5 150 5 51 52 rated cap. (*) 300 vac / 630 vdc std dimensions ? d max dv/dt at 390vdc (v/ s) part n umber b h l p 0.22 f 7.0 16.0 26.5 22.5 0.8 200 R463n 3220 - - 01 - x 0.33 f 8.5 17.0 26.5 22.5 0.8 200 R463n 3330 - - 01 - x 0.47 f 10.0 18.5 26.5 22.5 0.8 200 R463n 3470 - - 01 - x 0.68 f 11.0 20.0 26.5 22.5 0.8 200 R463n 3680 - - 01 - x 0.47 f 11.0 20.0 32.0 27.5 0.8 150 R463r 3470 - - 01 - x 0.68 f 11.0 20.0 32.0 27.5 0.8 150 R463r 3680 - - m1 - x 1.0 f 13.0 22.0 32.0 27.5 0.8 150 R463r 4100 - - m1 - x 1.5 f 13.0 22.0 32.0 27.5 0.8 150 R463r 4150 - - m1 - x 2.2 f 14.0 28.0 32.0 27.5 0.8 150 R463r 4220 - - m1 - x 3.3 f 18.0 33.0 32.0 27.5 0.8 150 R463r 4330 - - m2 - x 4.7 f 22.0 37.0 32.0 27.5 0.8 150 R463r 4470 - - m1 - x 1.5 f 11.0 22.0 41.5 37.5 1.0 100 R463w 4150 - - m1 - x 2.2 f 13.0 24.0 41.5 37.5 1.0 100 R463w 4220 - - m1 - x 3.3 f 16.0 28.5 41.5 37.5 1.0 100 R463w 4330 - - m1 - x 4.7 f 19.0 32.0 41.5 37.5 1.0 100 R463w 4470 - - m1 - x 6.8 f 20.0 40.0 41.5 37.5 1.0 100 R463w 4680 - - m2 - x 10.0 f 24.0 44.0 41.5 37.5 1.0 100 R463w 5100 - - m1 - x rated cap. (*) 275 vac / 560 vdc std dimensions ? d max dv/dt at 390vdc (v/ s) part n umber b h l p 0.22 f 7.0 16.0 26.5 22.5 0.8 200 R46kn 3220 - - 01 - x 0.33 f 8.5 17.0 26.5 22.5 0.8 200 R46kn 3330 - - 01 - x 0.47 f 10.0 18.5 26.5 22.5 0.8 200 R46kn 3470 - - 01 - x 0.68 f 11.0 20.0 26.5 22.5 0.8 200 R46kn 3680 - - 01 - x 0.47 f 11.0 20.0 32.0 27.5 0.8 150 R46kr 3470 - - 01 - x 0.68 f 11.0 20.0 32.0 27.5 0.8 150 R46kr 3680 - - m1 - x 1.0 f 13.0 22.0 32.0 27.5 0.8 150 R46kr 4100 - - m1 - x 1.5 f 13.0 22.0 32.0 27.5 0.8 150 R46kr 4150 - - m1 - x 2.2 f 14.0 28.0 32.0 27.5 0.8 150 R46kr 4220 - - m1 - x 3.3 f 18.0 33.0 32.0 27.5 0.8 150 R46kr 4330 - - m2 - x 4.7 f 22.0 37.0 32.0 27.5 0.8 150 R46kr 4470 - - m1 - x 1.5 f 11.0 22.0 41.5 37.5 1.0 100 R46kw 4150 - - m1 - x 2.2 f 13.0 24.0 41.5 37.5 1.0 100 R46kw 4220 - - m1 - x 3.3 f 16.0 28.5 41.5 37.5 1.0 100 R46kw 4330 - - m1 - x 4.7 f 19.0 32.0 41.5 37.5 1.0 100 R46kw 4470 - - m1 - x 6.8 f 20.0 40.0 41.5 37.5 1.0 100 R46kw 4680 - - m2 - x 10.0 f 24.0 44.0 41.5 37.5 1.0 100 R46kw 5100 - - m1 - x rated voltage (k=275vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) value of discharge resistor (table 2) rated voltage (3=300vac) mechanical version and packaging (table 1) tolerance: k (10%); m (20%) value of discharge resistor (table 2) *other resistors are avaible upon request. table 2 r code (x) 470 k? e 680 k? f 1 m? g 1.2 m? l 1.5 m? n 2.2 m? p 3.3 m? q 4.7 m? s 6.8 m? t 10 m? v all dimensions are in mm not for use in series with the mains. see www.kemet.com for more information. st a t e m e n t s o f s u i t a b i l i t y f o r c e r t a i n a p p l i c a t i o n s a r e b a s e d o n o u r k n o wl e d g e o f t y p i c a l o p e r a t i n g c o n d i t i o n s f o r s u c h a p p l i c at i ons, but ar e not i nt ended t o const i t ut e and w e speci f i cal l y di scl ai m any w ar r ant y concer ni ng sui t abi lity fo r a s p e c ific c u s to m e r a p p lic a tio n o r u s e . t h is in fo r m a tio n is in te n d e d fo r u s e o n ly b y c u s to m e r s w h o have t he r equi si t e exper i ence and capabi l i t y t o det er m i ne t he cor r ect pr oduct s f or t hei r appl i cat i on. a ny t echni cal advi ce i n fe rre d fro m th is in fo rm at i on or ot her w i se pr ovi ded by us w i t h r ef er ence t o t he use of our pr oduct s i s gi ven gr at i s, and w e assum e no obl i gat i on or l i abi l i t y f or t he ad vi ce gi ven or r esul t s obt ai ned.
|
